Top 10 typical forklift mishaps ， forklift operation ought to take note of these matters ！.

Do not undervalue the forklift at work. If the operation is not good, there will be major mishaps in mins, and there are lots of crashes entailing forklifts.

Instance 1: The forklift freight obstructed the vehicle driver's view, and the individual ahead can not be located, causing a rolling accident.
Case 2: In order to maintain the equilibrium of the forklift when raising hefty products, the workers used their body weight as the counterweight, which practically caused casualties.
Case 3: The size of the forklift freight surpasses the permitted width of the route and holds on the roadside rack, which nearly triggers an accident.
Case 4: Forklift is speeding up and surrender during a turn.
Case 5: The forklift vehicle driver did not see the pedestrian, and the pedestrian did not observe the forklift.
Situation 6: The forklift lifts the employees unlawfully, the forklift chauffeur does not wear the safety belt, the forklift lifter falls and the chauffeur is squashed when the forklift surrender.
Case 7: The forklift vehicle driver did not use a seat belt and dropped from the automobile when it rolled over and was squashed.
Forklift operation must focus on these matters ：.

Beginning.
1. Before beginning, observe the environments, and after confirming that there are no barriers that impede the safety and security of driving, beep the horn first and after that start.
2. For lorries with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) scale should be secure before beginning.
3. When the forklift starts with a lots, the chauffeur needs to first validate that the load is secure and reputable.
4. The beginning should be slow-moving and stable.

Driving.
1. When driving, the elevation between the bottom end of the fork and the ground must be maintained 300mm-400mm, and the mast needs to be tilted backwards. .
2. Do not raise the fork too high when driving. When going into and leaving the work site or while driving, be careful that there will be no challenges in the sky. When the lots is traveling, the fork has to not be elevated too high, which will impact the security of the forklift. .
3. After dumping, the fork ought to be reduced to the regular driving position before driving. .
4. When turning, if there are pedestrians or automobiles close by, the driving signal should be provided first. High-speed doglegs are restricted. High-speed sharp turns will certainly create the vehicle to lose side security and tip over. .
5. When the forklift is downhill, it is strictly prohibited to switch off the fire and slide, and it is forbidden to brake all of a sudden while driving with tons unless there are unique scenarios.
6. When the forklift is running, it should obey the traffic rules in the factory and must keep a specific safety distance from the vehicle in front. .
7. When the forklift is running, the load must remain in the lowest position that does not prevent the driving, and the gantry ought to be effectively slanted back. The tons will not be increased other than when stacking or packing. .
8. The height of the load have to not obstruct the vehicle driver's view. In special situations, when the item impacts the forward vision, drive at a low speed when reversing.
9. It is restricted to activate the ramp, nor to drive throughout the ramp. .
10. The safe driving speed of the forklift in the factory location is 5 km/h, and it should drive securely at a low speed when getting in the manufacturing workshop area. .
11. When the forklift is lifted, raised or driven, it is prohibited for employees to depend on the fork to hold things and play a stabilizing duty. .
12. If problems are located, they will certainly be fixed and reported in a timely way, and they will never ever operate with illnesses or hide them.

packing and unloading.
1. When fork-loading things, the distance between both forks ought to be adjusted as required to make the load of both forks well balanced and not manipulated, and one side of the thing should be against the rack. .
2. It is prohibited to work with a solitary fork or utilize a fork top or pull. In special situations, security warning signs need to be established to remind surrounding pedestrians. .
3. In the process of packing and dumping items, the forklift has to be stopped with the brake. .
4. The speed of the automobile need to be slow and steady. Beware not to roll the wheels on the dunnage, so as not to stretch the rolled objects and injure individuals. .
5. When utilizing a fork to fork the goods, the fork ought to be as deep as possible under the load, and it ought to be kept in mind that the fork suggestion must not touch various other products or things. The load must be stabilized with marginal back tilt of the gantry so that the load does not glide backwards. The pole can be tilted forward slightly when the lots is decreased to enable very easy placement of the load and removal of the forks. .
6. It is restricted to fork products at broadband and hit tough objects with the fork head. .
7. When the forklift is functioning, it is forbidden for individuals to stand around the fork, so regarding prevent the collapse of the goods and injure individuals. .
8. Overloading is restricted, and it is forbidden to make use of forks to lift personnel to participate in high-altitude procedures to stay clear of high-altitude falling accidents. .
9. It is not permitted to use the brake inertia to slip, put, round or roll items. .
10. It is not enabled to utilize forks to choose, transform pallet dump.

Leaving .
1. It is restricted to leave the forklift when the things on the fork impend. Prior to leaving the forklift, you have to unload the goods or reduced the fork frame.
2. Draw the parking brake handle to dead or depress the parking brake switch.
3. The engine is turned off and the power is removed. (Except for unique conditions, such as the driver does not leave the vehicle's line of sight and does not go beyond 1 min).
4. Get rid of the trick. .

Forklift Operation Precautions.
1. Prior to and after the forklift operation, the appearance should be examined, and gas, lubing oil and cooling water need to be added.
2. Check the safety efficiency of beginning, running and braking.
3. Check whether the lights and horn signals are complete and reliable.
4. Throughout the operation of the forklift, check whether the stress and temperature level are typical.
5. After the forklift is running, the external leak needs to likewise be inspected and the seals should be changed in time.

Forklift Safety Operation Specifications.
1. You need to check prior to leaving the auto;.
2. When you come across somebody in front of you throughout driving, you ought to send a signal at a distance of 5 m;.
3. The driving rate in the factory does not exceed 5 km/h;.
4. When driving, the nadir of the cargo should be 0.3 m ~ 0.4 m in the air;.
5. The turning need to not be as well sharp to prevent the propensity of " totally free switching";.
6. Running up and down the incline must be slow and consistent, and no turning on the incline is allowed.
7. Do not drive throughout the gradient. When the slope is higher than 10%, the lorry ought to be driven in reverse when declining;.
8. When the forklift employees bring the goods and move on, if they experience huge or heavy items and go to the motorist's line of sight, they must take the reversing exercise
.
The "Eight Prohibitions" need to be followed in the procedure.
1. Solitary fork operation is not enabled.
2. It is not allowed to lift the goods for cross country driving.
3. It is not allowed to Electric Forklift Truck for Warehouse get the goods by passing on the pallet with the fork.
4. It is not allowed to directly shovel chemicals, flammables and various other hazardous chemicals with forks.
5. It is not enabled to make use of inertia pressure to pick up the goods.
6. It is not enabled to make use of stopping force to exile round or easy-to-roll items.
7. It is not permitted to bring people to deal with the pallet or fork, and it is purely restricted to Electric Forklift Truck for Warehouse stand under the fork after the fork is raised.
8. Do not drive laterally on slopes
.
Parking is not permitted under the following problems.
1. Contours, slim roadways, train crossings;.
2. Sections with a longitudinal slope higher than 5%.
3. When there is an challenge on one side of the roadway, the contrary side of the section with the exact same length as the challenge need to be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844